Cheers gents, with a lot of heat and a massive hammer got it out

@Glynn123 thanks pal, will get it measured up then and get them ordered

@NINJA oops yeah, didn’t mean to @ you haha, cheers

@Glynn123 thanks for help, any chance you can attach a photo of the threaded bolt or a link please. The bolts I’m finding don’t seem to look like they’d work

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F152642149627

These look alright?

@NINJA thanks for the help appreciate it, already purchased the bolt kit so should be arriving soon and about to get new gasket set. Will be sorting that out when it arrives and also got some new reeds coming so will be a good opportunity to check all the bolts on manifold and carb. Also I have a 2005 Yamaha DT X, would this be ok as I’m aware they are fairly similar. https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F361287660164

@Glynn123 thinking of getting the more pricey Athena full kit from eBay, should be better

Thanks mate. I’ve had a look already and on the diagrams the item I’m looking for isn’t there...

Does anyone know where I can buy bottom headrace dust seals. Brought bearings but not ones that had them included.
Thanks

@mhbikesnbits thanks a lot. Do you know what else I would need as I don’t think that’s all parts in image attached
Cheers

Where can I find linkage bearings like the ones attached. I brought swingarm bearings thinking they were for this, obviously meant for swingarm bearings.

Ok perfect. Thanks a lot

Hi guys,
Removed head brace today and wanted to replace these bearings, although when searching for Yamaha DT X 2005 bearings others come up looking different...
Any advice? Cheers

Cheers gents, with a lot of heat and a massive hammer got it out

Would applying heat be a good or bad idea??

Anyone got an idea how to remove this bolt? Can’t remove the linkage...

Ah sound, thanks mate. Not the cheapest thing about haha

Can anyone tell me what the gear that isnt looking great called? Thanks.

@Calum lovely mate, thanks. What is the seal called do you know by any chance? Final drive seal?

Oil coming from the left crank case side / sprocket. Any idea why this is happening? Think it’s a seal gone..

https://m.imgur.com/VjwNJu4

Recently my DT has been pouring fuel out the overflow, when it’s at idle or even when I’m going along. I have taken apart the carb (just the float bowl) to have a look to see what’s happening and seems to be the float bowl getting stuck but not a clue why, cleaned it put back together multiple times and still happening. Best thing to do would be completely strip the carb and clean / replace anything if needed to? Or buy a new one?
Seen a service on EBay that does this but for £50...

Also due to the fuel leaking, I left a junction and creating a small puddle of fuel that I didn’t know about I lost traction when I went over it and dropped bike which hit the exhaust, ripping out the studs... would repairing the threads or installing new ones be easy to do?

Cheers

Emptied fuel tank, just clean fuel. Cleaned it out also. Cleaned air filter also and still getting blocked... any recommendations? Shall I try size up the jet?

Ok sound, pictures of the inside of the carb I’m guessing? Haha

Would what I’m putting on my air filter have something to do with it?

@ringdingding and haven’t a clue about the condition of the inside of tank

@ringdingding no filter for the fuel, and very hard to tell as the hole is tiny so can’t make it out

Recently my bike doesn’t want to idle, I stripped down the carb and completely cleaned it as well as the jets twice. The idle jet was blocked both times I cleaned it, after putting it back together it would run as normal until the idle jet blocked again and then would have to be constantly revving it to avoid killing the bike at the lights...

Any ideas why this is happening?
Cheers guys

Never brought Silkolene before so watched to check before purchase.

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F331962365416

Will this oil be suitable for my DT, gearbox oil obviously
Cheers!

Anyone know the torque measuurements for the left and right casings? And exhaust if it had one, thanks.

@declan thanks for clearing that up

@jakeyboy oops, had another look and found some measurements but nothing for engine casing torque & exhaust. Much appreciated!

@NINJA sound, thanks. Just ordered had a brief look through the online manuals and haven’t seen anything regarding torque settings for the bike. Any idea where I can find this?
Cheers

@Irongamer727 cheaper than buying individually and less hassle

Has anyone put on front axel sliders on stock DT suspension? As both sides are different diameters.

@Glynn123 thanks pal, will get it measured up then and get them ordered

@NINJA oops yeah, didn’t mean to @ you haha, cheers

@Glynn123 thanks for help, any chance you can attach a photo of the threaded bolt or a link please. The bolts I’m finding don’t seem to look like they’d work

Hi, wanting to put some crash bungs on my DT, anyone done this before that has some advice as don’t want to spend £70+ on front and rear r&g ones. Thanks!