So Close!...
-
Bud, I know. Weird thing is the last pristine one I bought was off of fleabay! It was about £20 as well!! Before that it was the pristine 3mbp head & barrel with the entire 3wire servo & p/valve setup for £140. There are genuine sellers out there who aren’t all sheepled into the whole artificial Dtr pricing thing! It’s just time consuming to find them…
I do have a 4fu I can use, just not sure about the squish, ect…I dinged my (genuine!) fork seal putting it in yesterday 🤬 luckily I found a geezer selling 2 genuine seals for £14 last nite. I also got 2 genuine seal washers for £10 (just not sure of the point or proper placement) and indulged in a fork seal fitting tool for £12, I just hope it works better than my chipped big flathead screwdriver!
… -
Does everybody else balance the tyres on their bikes? All the bikes I’ve owned and ridden and I’ve never, ever had to balance the tyres! Never even though about it. Yet my dtr used to ride like a pneumatic drill and I didn’t realise it wasn’t a ‘characteristic’ 🥴 Bad enough when it’s just one doing it! Throw in the rear with the rim~lock and it’s no wonder I didn’t like going over 60mph!! Bucking Flipping Bronco**!!**
️ … -
Did you upgrade your front master cylinder when you fitted the brembo 2pot calliper? If so what size? I’m gonna guess you used an aprilia one!
…Just trying to find out about front master cylinder sizes, mine has a 13mm which is interesting. The 13mm rear wasn’t ‘enough’ to work a 35mm front calliper when I fitted it on the rear…
I’ve found a few different nissin ones from different bikes. Triumph do a few 14mm & 5/8in ones.
There are loads that look identical to the dtr125 ones from different 125’s which can be had for £20-30 (minus the Dtr tax which would make it £60-80
) in mint condition!… -
Cheers bud, I forgot you run ally wheels…
Do you have any knowledge about anybod that could manufacture a centre ‘hat’ rotor for the front hub? I would love to get a centre bit made so you could ‘bolt’ a floating disc to it. It shouldn’t be too difficult because there’s no offset to worry about. I’ve read that they can be made from aluminium, which shouldn’t be too hard. Just some CNC work and figuring what outer disc to fit/match it to. It’d be harder to make the calliper mounting plate to fit a 2 pot calliper too it, surely?…
Any thoughts?… -
How bad are rear wheel bearings to replace?…
I’ve done one before but it was nearly 35 years ago. I seem to remember lump hammer and giant screwdriver, ala chisel? I seem to remember having to depress the centre tube to allow access to the bearing from the opposite side? Any help/tips appreciated
… -
I’m not a daytime/morning person but I will oblige when the good weather finally breaks!
…Has anyone ever had a water pump seal fail? I’ve had some contamination problems with my gear oil, it’s grey and emulsified. Horrible state! The only things I can think of are the pump seal letting a small amount of liquid into the gearbox, or possibly condisation from cold damp air during the winter. Which is a stretch of the imagination
… -
Finally got round to doing the forks! Got new genuine oil seals from fleabay for less than a tenner each, but try and find the top dust seals!!…
Made sure the bolts are separated from the aluminium by using CT1 sealant to ‘encapsulate’ the fuxors! Doesn’t hurt leaky copper washers either;) …
Used 1 & 1/2 extension bars to use the 27mm hex/Allen adapter to hold the inners in place made torquing it up real easy…
Finally fitted these puppies in the forks!…
Will fit the forks to the bike soon as possible, weather permitting
… -
I thought about it, even bought some (YZ) that had been fitted to a Dtr by a previous, but the reality of how massive tall they are just put me off. Getting the right donors is definitely the ‘ting’
The standard forks are way too soppy… -
Has anyone else noticed that when you tighten up the front wheel spindle it wobbles up-down/side-side a little? I’ve had this with different forks and spindle combinations! Is this normal?!…
I’ve noticed that the gap on the speedo side is nearly 5mm more than the disc side, normal or not?…
Ta for any insight
… -
I’m guessing both mine are a bit bent!
I recon it’s what happens when you ride a bike any distance with 1 fork seal gone (which to my shame I have done) and put too much pressure on side, especially the side with thread…Both of mine were bent to hells fuck! If I had tog gotten a new one I would never of realised how fuxin awful my bike was handling at any speed over 50mph!
Nearly every thing that comes into contact with my Life seems to be just ‘that little bit wrong!’ It’s fuxin exhausting! Whatever happened to harmony, balance, in the World. The fuxin Holocene is wasted on money grubbing Torrie, Nazi, Capitalist fuckin head up their arses, “it doesn’t matter what I do cause it’s all just a dream” misery mongers!!
Please bring on the Zombie apocalypse, or some way of thinning the herd that is mankind. COVID wasn’t harsh enough!…Sorry, my Rant is over
I’m tired of living in a “world full of Wonders” not a “Wonderful World” that I believe this ball of spinning dirt could be….
️ -
This post is deleted!
I rarely use my bikes and I certainly don't go at any speed
No play just the odd notch 🤬 Good job I bought some when I got the bike! 
