DT200WR restoration project pic heavy
-
wrote on 17 Jan 2019, 20:33 last edited by
@NINJA yes, this engine had a fair few leaks I sorted today
Oil pump
Gear lever seal
Water pump.
Also putting the water pump pipe back in caused many problems, took so many attempts to get it to seal.
But now have a fully functioning to 2stroke pump
.. as it was from the factory. -
@NINJA yes, this engine had a fair few leaks I sorted today
Oil pump
Gear lever seal
Water pump.
Also putting the water pump pipe back in caused many problems, took so many attempts to get it to seal.
But now have a fully functioning to 2stroke pump
.. as it was from the factory.wrote on 17 Jan 2019, 20:48 last edited by@Louis-James Nice one, I feel your pain, as I've very recently been there myself. :pouting_face: :pouting_face: :pouting_face:
It sounds like either a lot of gaskets have perished or not been fitted properly in the first place? Either way an overhaul of em all may be prudent???
-
@Louis-James Nice one, I feel your pain, as I've very recently been there myself. :pouting_face: :pouting_face: :pouting_face:
It sounds like either a lot of gaskets have perished or not been fitted properly in the first place? Either way an overhaul of em all may be prudent???
wrote on 17 Jan 2019, 21:14 last edited by@NINJA always when someone else does work
I've thoroughly checked all over. The top end had been rebuilt with a wiseco piston.
I did check that.But one of the last bits done to the engine was a new clutch and water pump seal.
-
@NINJA always when someone else does work
I've thoroughly checked all over. The top end had been rebuilt with a wiseco piston.
I did check that.But one of the last bits done to the engine was a new clutch and water pump seal.
wrote on 17 Jan 2019, 21:28 last edited by@Louis-James Well hopefully the only bumps you'll see from now on, will be the ones you are jumping over MX styleee!!!
-
wrote on 21 Jan 2019, 18:53 last edited by
So the oil pump was not flowing. Took it off and the outlet was block. Removed the hose tail and I drilled the smaller bore. Oil now flows through.
Without taking the pump alart again I am unsure if I have drilled too deep and the oil is bypass internally. By blowing through it and operating the throttle.. it doesn't seem to flow more or less on throttle position. Does there need to be drive to the pump and is it a variable gear inside is what changes the flow?
So going to have to inspect.
Or compare to another.Also bike cuts out when put into gear with stand up or down.. I think it's a faulty sidestand switch
A few little things to sort
Anyway.. a few pics
-
wrote on 21 Jan 2019, 19:05 last edited by
Bike looks superb. Done an excellent job there. Definitely will be on that infamous hall of fame...
Yeah side stand switch is common on all bikes. Should be relatively simple to figure out.
Hopefully it's the switch and not the CDI.
Yeah pumps can be weird to diagnose, better run premix whilst you're figuring it all out!
-
Bike looks superb. Done an excellent job there. Definitely will be on that infamous hall of fame...
Yeah side stand switch is common on all bikes. Should be relatively simple to figure out.
Hopefully it's the switch and not the CDI.
Yeah pumps can be weird to diagnose, better run premix whilst you're figuring it all out!
wrote on 21 Jan 2019, 19:08 last edited by@Calum thanks a lot man.
It didn't have a side stand switch before.
It was looped (wiring present) but I bought a universal switch. I'll do a circuit test on it.Yes I'm running premix arm. Engine is sweet!
No leaks! -
@Calum thanks a lot man.
It didn't have a side stand switch before.
It was looped (wiring present) but I bought a universal switch. I'll do a circuit test on it.Yes I'm running premix arm. Engine is sweet!
No leaks!wrote on 21 Jan 2019, 20:04 last edited by NINJA@Louis-James The bike looks mint bud - TOP JOB!!! :thumbs_up_light_skin_tone:
Have you ridden her yet???
-
@Louis-James The bike looks mint bud - TOP JOB!!! :thumbs_up_light_skin_tone:
Have you ridden her yet???
wrote on 21 Jan 2019, 20:15 last edited by@NINJA thank you
I rode it before I stripped it down.... rapid!
I've just got a few little things to sort out before taking it for a proper spin -
@NINJA thank you
I rode it before I stripped it down.... rapid!
I've just got a few little things to sort out before taking it for a proper spinwrote on 21 Jan 2019, 20:25 last edited by@Louis-James COOL she should go better with the upgrades, let us know how she handles.
-
wrote on 21 Jan 2019, 20:53 last edited by
@NINJA will do not too keen on knobblies on the road.. but definitely suits it physically
-
@NINJA will do not too keen on knobblies on the road.. but definitely suits it physically
wrote on 21 Jan 2019, 21:10 last edited by@Louis-James She's an enduro, so she should go anywhere you wanna take her!!!
-
wrote on 22 Jan 2019, 22:24 last edited by
Here's a running video.
https://youtu.be/s9rmjz71dsUThat oil pump was definitely blocked inside the casting..
Got another on order. -
Here's a running video.
https://youtu.be/s9rmjz71dsUThat oil pump was definitely blocked inside the casting..
Got another on order.wrote on 23 Jan 2019, 00:18 last edited by@Louis-James She sounds just like a proper 2 stroke should!!! :grinning_face_with_smiling_eyes: :grinning_face_with_smiling_eyes: :grinning_face_with_smiling_eyes:
-
@Louis-James She sounds just like a proper 2 stroke should!!! :grinning_face_with_smiling_eyes: :grinning_face_with_smiling_eyes: :grinning_face_with_smiling_eyes:
wrote on 23 Jan 2019, 20:10 last edited by@NINJA cheers
Can anyone help find me an original wr200 or dt200wr luggage rack.
I can't find it on the diagrams but many of them seem to have them from factory.
Part number?
Maybe only certain countries had them.
-
@NINJA cheers
Can anyone help find me an original wr200 or dt200wr luggage rack.
I can't find it on the diagrams but many of them seem to have them from factory.
Part number?
Maybe only certain countries had them.
wrote on 23 Jan 2019, 20:23 last edited by@Louis-James Is that the original one which came with the bike? If so why not just get it re-powder coated???
-
@Louis-James Is that the original one which came with the bike? If so why not just get it re-powder coated???
wrote on 23 Jan 2019, 20:36 last edited by@NINJA it's not mine.. just a picture I found online
-
@NINJA it's not mine.. just a picture I found online
wrote on 23 Jan 2019, 20:51 last edited by@Louis-James AAAHHHH OK - shame but I'm sure that you'll find one from somewhere???
-
wrote on 25 Jan 2019, 14:23 last edited by Darty
-
wrote on 25 Jan 2019, 15:06 last edited by
Here's the spare set of wheels and tyres that came with the bike.
Top brand tyres to be fair.
The rear wheel is a straight swap (3bn hub with 2.15 alloy rim)
However the front wheel has a different hub... Like the late 90s yz.
If the brake discs faces offset is correct then I could turn the hub in a lathe to get the brake disc to fit,Not really sure what I want to do with these wheels. Part of me wants to build them up with purple hubs and stainless spokes.
I'd probably sell the tyres as they are MX ones
