Husky cr 250
-
@minia the bike stalls in gear after like 5 seconds unless I blip it it’s a shame really clutch will cost 60 and then the wrench it’s money I don’t have but that’s life from what I’ve read no manual was made for these bikes it don’t die in gear if it’s say on the garden and not properly warmed up
-
@declan I think I’ll get the cover off soon lads the shop didn’t even put the plug in it wasn’t even tight so maybe there’s a chance it’s on low oil or wrong oil?
@declan Of course there is a manual mate. Give it an oil change if you think it is required. Can't go wrong with that.
http://www.husqvarnafactory.nl/pdf/2004/2004_WSM_WR-CR_250.pdf
Yamaha DT125R Blue 2002, XT 125 1982, Yamaha WR250Z 1992, BMW GS650F 1994, Benelli BN302 2015
-
@declan Of course there is a manual mate. Give it an oil change if you think it is required. Can't go wrong with that.
http://www.husqvarnafactory.nl/pdf/2004/2004_WSM_WR-CR_250.pdf
-
@declan Of course there is a manual mate. Give it an oil change if you think it is required. Can't go wrong with that.
http://www.husqvarnafactory.nl/pdf/2004/2004_WSM_WR-CR_250.pdf
-
I did that on my DT. I managed to unscrew it somehow anyway. Luckily I have a spare engine so I could fix it right away.
-
Is that snapped off or missing?
Either way there is your problem.
No biggie though, easy fix.
-
Is that snapped off or missing?
Either way there is your problem.
No biggie though, easy fix.
-
@calum the threaded cylinder is snapped so I have no thread to screw one back into unless I can helicoil or something similar
-
@declan It's not totalled mate. You can take it to someone competent, they will just drill the existing bolt out without damaging the thread. Simples.
-
@calum it’s not there bud the entire thread that the bolt goes into is gone completely there’s no left over bolt
@declan Oh ryt, yeah, you would need to tig it back on.
I've seen these happen before when someone tries to under the clutch center bolt without the proper tool.
Yeah, again, it's not the end of the world. A piece of bar can be machined out and tig welded into place. But you're probably better off getting a new basket.
Always Originate, Never Pirate!
-
@declan Oh ryt, yeah, you would need to tig it back on.
I've seen these happen before when someone tries to under the clutch center bolt without the proper tool.
Yeah, again, it's not the end of the world. A piece of bar can be machined out and tig welded into place. But you're probably better off getting a new basket.
-
@declan Well at least you know what the exact problem is now, for good measure though I'd disassemble that clutch entirely and see what it looks like... could give you an idea on how the previous owner treated it.
Yamaha DT125R Blue 2002, XT 125 1982, Yamaha WR250Z 1992, BMW GS650F 1994, Benelli BN302 2015
-
@declan Well at least you know what the exact problem is now, for good measure though I'd disassemble that clutch entirely and see what it looks like... could give you an idea on how the previous owner treated it.
-
@declan Well at least you know what the exact problem is now, for good measure though I'd disassemble that clutch entirely and see what it looks like... could give you an idea on how the previous owner treated it.
-
@minia don’t suppose you could ask your pals if they know of a clutch hub that drops right in I’ve found one or two but can’t be
sure@declan Honestly, I don't think they'll know. They're young fools so it's more about enjoying it until it breaks rather than keep it running... I can ask them if they know contacts of people who'd be able to supply the parts you need. But since my mates are french it will complicate things. You can look online on forums and facebook.
As long as you have the part numbers of what you need, you can phone up any motorcycle parts distributor and hope that if they don't have the part they know the contact details of someone who can get it for you.
Yamaha DT125R Blue 2002, XT 125 1982, Yamaha WR250Z 1992, BMW GS650F 1994, Benelli BN302 2015
-
@declan Honestly, I don't think they'll know. They're young fools so it's more about enjoying it until it breaks rather than keep it running... I can ask them if they know contacts of people who'd be able to supply the parts you need. But since my mates are french it will complicate things. You can look online on forums and facebook.
As long as you have the part numbers of what you need, you can phone up any motorcycle parts distributor and hope that if they don't have the part they know the contact details of someone who can get it for you.
