Power valve issue
-
Forced the valve open while engine running and goes like stink top end. Have noticed since I done that and tuned the ignition off and on and start engine it starts to move as it should for a few revs then stops moving again. I'm taking a guess it's the solenoid?
wrote on 16 Apr 2018, 18:58 last edited by@thechompster It's a motor on these. So could be the brushes.
Are you sure the valve isn't just gunked up.
Would be worth dismantling the assembly and cleaning it thoroughly.
-
@thechompster It's a motor on these. So could be the brushes.
Are you sure the valve isn't just gunked up.
Would be worth dismantling the assembly and cleaning it thoroughly.
wrote on 16 Apr 2018, 19:06 last edited by@calum it could possibly be gunked up but would it not move when you turn the ignition on?
-
@thechompster It's a motor on these. So could be the brushes.
Are you sure the valve isn't just gunked up.
Would be worth dismantling the assembly and cleaning it thoroughly.
wrote on 16 Apr 2018, 19:09 last edited by@calum do you have a link for how to remove power valve at all?
-
@calum do you have a link for how to remove power valve at all?
wrote on 16 Apr 2018, 19:34 last edited by@thechompster No, just take the two powervalve end caps off. The offside powervalve housing has a bolt to keep the two pieces together, make sure you don't lose the locating dowels as they're prone to falling out. You'll want to lubricate it with WD40.
-
@thechompster No, just take the two powervalve end caps off. The offside powervalve housing has a bolt to keep the two pieces together, make sure you don't lose the locating dowels as they're prone to falling out. You'll want to lubricate it with WD40.
wrote on 16 Apr 2018, 20:16 last edited by@calum ok thanks for the help. With give it a go.
-
@calum ok thanks for the help. With give it a go.
-
wrote on 17 Apr 2018, 19:17 last edited by
Took the exhaust off. A bit dirty in there but rotates easy enough. Goes through the cleaning process nice and easy so all I can do now is change the servo and hope it sorts it.
-
wrote on 17 Apr 2018, 20:47 last edited by
Odd that it'll do the cleaning cycle fine but not run right.
I'd be more inclined to say faulty CDI more than anything. I guess these bikes are just starting to show their age.
-
Odd that it'll do the cleaning cycle fine but not run right.
I'd be more inclined to say faulty CDI more than anything. I guess these bikes are just starting to show their age.
wrote on 17 Apr 2018, 21:57 last edited by@calum yeah I guess they are.apart from that it runs lovely. Will change the servo. If that doesn't do it just the cdi left I guess.
-
wrote on 18 Apr 2018, 19:12 last edited by
A friend had a faulty servo, sometime during a ride where the PV was open, it would leave it open. Other times just seem erratic. I believe the gears in the servo was toast.
-
A friend had a faulty servo, sometime during a ride where the PV was open, it would leave it open. Other times just seem erratic. I believe the gears in the servo was toast.
wrote on 18 Apr 2018, 22:18 last edited by@jens-eskildsen ok thanks mate. Very helpfull
Will try another servo then and see what happens. -
@jens-eskildsen ok thanks mate. Very helpfull
Will try another servo then and see what happens.wrote on 19 Apr 2018, 06:42 last edited by@thechompster just out of interest, what spark plug are you running??
-
@thechompster just out of interest, what spark plug are you running??
wrote on 19 Apr 2018, 10:06 last edited by@mitch_350z iridium spark plug
-
@mitch_350z iridium spark plug
wrote on 19 Apr 2018, 11:22 last edited by@thechompster does it have the resistor in it the 'r' in the spark plug type as this can cause issues with the operation of the valve
-
wrote on 19 Apr 2018, 12:19 last edited by
I've always ran br9eix on my bikes with no isses.
I think that's the one at least.
-
@thechompster does it have the resistor in it the 'r' in the spark plug type as this can cause issues with the operation of the valve
wrote on 19 Apr 2018, 12:36 last edited by thechompster@mitch_350z the one below. Br9eix.
-
wrote on 19 Apr 2018, 15:06 last edited by
Me too, br9eix
-
@mitch_350z the one below. Br9eix.
wrote on 19 Apr 2018, 16:49 last edited by@thechompster my mistake, I meant without the 'r' lol if it hasn't got the resistor in it the valve finds a mind of its own. You can hear the exhaust note change as you ride
-
@thechompster my mistake, I meant without the 'r' lol if it hasn't got the resistor in it the valve finds a mind of its own. You can hear the exhaust note change as you ride
wrote on 19 Apr 2018, 22:08 last edited by@mitch_350z I see. Where is the resister?