Yamaha DT 125R 1994 project
-
Could someone identify what exhaust is this? https://www.tori.fi/vi/65670465.htm
-
My ported suzuki pv moped: https://www.youtube.com/watch?v=Ds1trRkr22g
-
So i had little worn rear tire so this happened... little backfire also. https://www.youtube.com/watch?v=GruRc--3zNA
-
@Calum
Check out his pootube vid, then ask yourself why you asked
...
Sorry, did I miss your dry humour?
-
So basically i was just revving the hell of it for about 20 seconds went driving and felt weird. Engine stalled kickstart stuck.
So i opened the engine and there was bearing pieces over piston so rod bearing failure. There was sand in engine via bad air filter from previous owner. Also the piston was ridden about 1500km and the ring cap was 0,7mm on the top one and 0,5mm bottom one. And the needle bearing was shot. So the engine would have failed eventually. I think i know now what the werid side noise was.
https://i.imgur.com/jsw8S7K.jpg -
So basically i was just revving the hell of it for about 20 seconds went driving and felt weird. Engine stalled kickstart stuck.
So i opened the engine and there was bearing pieces over piston so rod bearing failure. There was sand in engine via bad air filter from previous owner. Also the piston was ridden about 1500km and the ring cap was 0,7mm on the top one and 0,5mm bottom one. And the needle bearing was shot. So the engine would have failed eventually. I think i know now what the werid side noise was.
https://i.imgur.com/jsw8S7K.jpg@jonne123 said in Yamaha DT 125R 1994 project:
So basically i was just revving the hell of it for about 20 seconds went driving and felt weird. Engine stalled kickstart stuck
Is called seizure by heat or lack of oil. Or screaming from cold start. Or all of the above...
“There was sand in engine via bad air filter from previous owner. “
Bad you never checked as well though bud (the filter) bike stuff 101
The rest is lost in translation, to me.
-
-
Well it had rebuild top end and i changed the filter right away but didn´t realise that there was sand in the intake until month ago i cleaned it. Also the engine was making weird side noise probably from crankshaft. There was oil and mixture was rich.
-
@jonne123
YouTube & your back tyre says otherwise!
An engine rebuild is always around the corner on a second hand bike, no matter what the previous owner says. If you do as good a job with the engine as you did with the rest of the bike, you’ll end up with a good, tight bike. Just run it in on less than 90% throttle!!
... -
Yeah... But it was like month after burnout. The engine has always made weird side noise. But it would really been sad if it happened during next summer. The bearing would failed. Also the needle bearing is totally worn and piston rings. Remember to clean your air filter!
But now plans for the project:
-Fix rust and paint some parts.
-Clean aluminium parts.
-Fix engine
-Replace worn parts.
-Sticker kit or wrap for plastic parts.
-Possible some tuning parts.
I´m open for suggestions!
-
Yeah... But it was like month after burnout. The engine has always made weird side noise. But it would really been sad if it happened during next summer. The bearing would failed. Also the needle bearing is totally worn and piston rings. Remember to clean your air filter!
But now plans for the project:
-Fix rust and paint some parts.
-Clean aluminium parts.
-Fix engine
-Replace worn parts.
-Sticker kit or wrap for plastic parts.
-Possible some tuning parts.
I´m open for suggestions!
-
I know that the crankshaft bearing failed. But there could be something else like a bearing.
-
@jonne123 Yes, but WHY did the crank bearing fail?
There is no point in rebuilding it if you don't understand why it failed.
...