Missing some wires for the cdi

[SpookDog]

@dan28

Does your bike run? If so what’s the problem?
Do you have a power valve servo fitted? The early 1988~1996 bikes have a servo with 3 wires (not 5) a single black with white (or yellow!) stripe wire and a twin connector with a black wire and a brown wire...

I have some spare wires in a box, how many do you need?

[dan28]

@SpookDog said in Missing some wires for the cdi:

@dan28

Does your bike run? If so what’s the problem?
Do you have a power valve servo fitted? The early 1988~1996 bikes have a servo with 3 wires (not 5) a single black with white (or yellow!) stripe wire and a twin connector with a black wire and a brown wire...

I have some spare wires in a box, how many do you need?
The dtr engine is in a different bike
I ve not tried to start it yet
The loom had to be chopped an lengthend
I ve wrote down that cdi black an yellow goes to red an white
An that blue an yellow from.cdi goes to black an yellow in the loom but that was ages ago an now I can't find either wire in the loom side

[HOTSHOT III]

@dan28 said in Missing some wires for the cdi:

The engine an loom are 1989 the cdi is I believe 3nc the writing has worn off
To make it easier I ll list all the wires that the cdi has in case I got the code wrong

Right side of cdi
Male 2 pin plug
white/ red . Wire
Black . Wire
Female 2 pin plug
Green/ white Wire
Black an red wire
These plugs go to stator
Correct

Left side of cdi
2 pin plug
Dark blue wire
Light blue wire
This is for neutral an oil light
Correct

Twin Black wire from cdi goes to earth
Correct

Black / white from cdi goes to black / white in loom not sure what it's for ?
This is for the kill button on the handlebars

Orange wire from cdi goes to coil ?
Correct

Blue / yellow from cdi should go to Black/ yellow I can't find it in the loom ?
Blue/yellow from CDI should go to blue/yellow on the loom, a single bullet connector. This goes to the sidestand switch

Black / yellow from cdi should go to.red an white possibly power valve?
Black/yellow from CDI is the YPVS signal wire, goes to black/yellow on the 3-wire YPVS servo. The only red/white wire on the 3NC loom is the short section of the battery +ve lead containing the fuse holder

Did I just respond to this on one of the DTR Facebook pages? I posted up a pic of the 3NC loom, will try and upload it onto here

[HOTSHOT III]

@dan28 3NC wiring diagram below

[SpookDog]

Please stop posting full on quote mode peeps! It’s making me dizzy trying to read posts!!...

[Calum]

@HOTSHOT-III You can embed images bud:

Just got to use the right link: https://live.staticflickr.com/65535/52172141696_84e3b69382_b.jpg

[dan28]

thanks hot shot
yes that was me on fb
so blue an yellow is for sidestand
i have a black with yellow stripe single bullet connector thats labelled as goes to red an white i think this is meant to go to the servo
i m not sure what code my cdi is dont think its 3nc

[SpookDog]

@dan28

Black with yellow stripe goes to 3wire servo. Along with back wire & brown wire double block connector from the loom...

[HOTSHOT III]

@dan28 Yes that's correct, brown is main feed from the ignition switch on Yamahas and obviously black is earth. Interestingly if you apply battery voltage to the black and brown wires of a serviceable 3-wire servo it will perform its cleaning cycle even when removed from the bike as the control circuit is inside the servo itself and the black/yellow signal wire from the CDI just tells the servo the engine speed.

Only other CDI unit I can think of could be a 3BN from the very first 1988 DTR; I think the wiring is very similar to a 3NC but you'd probably have a 26mm round slide carb if that's the case.

[HOTSHOT III]

@Calum Thank you! How do you obtain a staticflickr link from the image please? Had a nose around last night and couldn't find it, maybe because I'm using the free version of Flickr?

[Calum]

@HOTSHOT-III Uhh, you edited your post with the URL in it.

I don't use flicr personally, but Right Click + Copy Image Location ought to give you the URL.

[HOTSHOT III]

@Calum OK cool, thought I'd still done something wrong as the actual image still didn't appear like in your comment above. Still the OP can access the wiring diagram so all good

[Calum]

@HOTSHOT-III Take the URL and put it in side the () of a []().

The syntax is Markdown

[HOTSHOT III]

@Calum Finally sorted as you can see above!!

Turns out on my computer you have to click the download link on a Flickr photo, choose the size you want, THEN copy and paste the URL. Might be because I'm still using the Victorian technology that is Windows 7?

Anyway thanks for your patience

[Calum]

@HOTSHOT-III Yeah, I only use Linux and Firefox.