-
@mhbikesnbits That's a good price, I wish the coaters around here were that cheap. I got quoted £100 just for a set of yokes. :face_screaming_in_fear:
Rattle can to the rescue!!! :grinning_face_with_smiling_eyes:
-
@NINJA wow really what area are from , that’s expensive he does a top notch job too restores bikes himself so he knows the crack what’s good to paint and what’s not
-
@mhbikesnbits Berkshire, sadly there's not too many coaters interested in 'small one off' type jobs in this neck of the woods.
-
It's difficult to find a coaters "sympathetic" to restoration as opposed to commercial work, you need an enthusiast. I rate my coater highly but even them I have returned the odd bit, but I am picky (why should I not be, I am paying). Maybe being a regular (ish) customer helps but the cost is reasonable to me, when I first went there made clear my expectations and they have accommodated my requirements. I am lucky there are several local to me but not all finishes available, need to find someone local who does anodising, would prefer that to painting my black bits.
-
@oldman I have a few anodisers around me I did think a couple of days ago actually,
maybe I should of, but it was just easier just send a load in one go for powder coat as the price is good for me and quality is amazing,the 3et was listed on eBay for a while from a seller in Poland it had damage on the engine case as seen in a previous post that I have repaired which might have put people off but with much thought I decided to pull the trigger
-
Nice project! The crankcase damage in this engine occured because the owner didnt pay that much attention to the condition of the chain and sprockets, I recommend you changing the drivetrain from 428 to 520 for better strenght(just look for DT200R chain and sprockets, everything will fit bolt-on) and also use the chain lower guide(new avaible to buy cheap at yamaha dealer) in good condition, if you do that there will be no more problems with chain causing damage to the crankcases.
I raced the guy on that DT200R in 2016, it was only amateur cross-country type of championship but the WR200 turned out to be superior to DT :face_with_stuck-out_tongue: , 2 years later he sold me the bike.
Heres a pic of that DT, looked better than when i got her.
-
@Challenger the dt is already having a lot of it’s power sapped a bigger chain is way overkill
-
@Challenger thanks for sharing buddy cracking picture, I would image yes maybe the case was damaged because of the chain and sprocket buyer didn’t specify why, could be a number of ways,
I’m unsure what chain size and sprocket size to use yet need to some research after I’ve rebuilt the engine and fitted it to the frame, Id prefer to get it to this stage before I start planning how to engineer the bike
-
I’ve ordered and new workshop so planning that at the moment which is why there has not been much attention to the dt, also rebuilding my 1980 rm 80 engine, which I need to metal spray the crank as the bearing is to slack on one side of the crank wouldn’t want it spinning one bearing that’s for sure,
Just for fun anyone want share a picture of there workshops/ garage ?
-
I also planning on doing restoration services for bikes, any model any part any type of restoration from nuts and bolts to full bike rebuilt anything you like what I’ve done on my build I can do, so if that’s somthing that Interests you guys let me know
-
engine back from the Powder coaters, happy with the results looking forward to rebuilding it up, just got to mill the writing on the custom ypvs cover as masking it wouldn’t look right
I also need to spray the plastic covers because these can’t be powder coated
-
I cant belive how fantastic all this is looking i really hope mine looks as good at this once its done.
-
@Walney-Reptiles thanks for your kind words quite abit to do yet till it’s done, but I really like your project too think your doing a amazing job
-
@mhbikesnbits Your welcome mate, and thanks very much
what time next year do you think you will have finished, i reckon by april next year mine should be completed
