TDR125 4GW
-
So you are telling me I could have ran a dome top piston in my 4FU nikasil plated barrel.
The only reason I ask is because I was told I could only run a 56mm flat top in my cylinder by pjme?.
-
So you are telling me I could have ran a dome top piston in my 4FU nikasil plated barrel.
The only reason I ask is because I was told I could only run a 56mm flat top in my cylinder by pjme?.
@tdr125greg PJME know what they are doing.
You can run whatever you want.
But you would want to have the combustion chamber reworked.
If you have a 4FU head then you should notice a restrictive combustion ring around the chamber.
For £30 odd quid Mick Abbey will grind that out and put a nice squish band there. 80% of the power of a two stroke comes from the head. So getting this part right is crucial.
Telling your tuner that you are going to run a domed piston, will allow them to correct the squish band.
My advice would again be do this with another, specifically designed, engine.
The Rotax 122 engine that I am building comes stock with a flat top piston. But I intead to rework the head and run a domed.
Running at higher compression puts you at risk from detonation. This is an engine killer. To avoid this you need to retard the ignition, or up the fueling.
So it's not always clear what the best path is.
I have had a few 4FU's but never saw a build through to the finish.
-
Thankyou calum I will take everything into consideration and make a path for myself. I solidly agree on a second engine but for now I'd rather get the current engine running smoothly and swap the front end.
When I have a nice set up I will give it the beating heart it deserves.
-
You cant run a Domed piston in a 4FU? Wouldn't it hit the head? I've got a 4FU head, and they never came with combustion rings, only 2RK/3BN's?
A Flat top piston doesn't interfere with your transfer ports as much as a Domed piston, so you can take advantage of scavenging with correct porting and a proper exhaust,
The 4FU seems to have larger volume crankcase transfers than a 3MB?
I'm running .6mm squish and a 134cc heavy Top end porting on a 3MB barrel. Looking at 25bhp maximum on 97octane. Most power will be made by the cylinder head itself, the barrel is aiding it along.
No doubt moving torque, and not that much more of it to very high RPM, will only make you come to be very efficient at going up and down the gearbox quicker to keep the thing in the right rev range.
Depends what you want from it, i'd say get the ports cleaned up, but don't change the Port timings at all, and just run her standard. These engines don't make power at all like a Rotax!
I've been bulding a race setup for mine for a while now, yet to know proper results tho
Keep it real
-
You cant run a Domed piston in a 4FU? Wouldn't it hit the head? I've got a 4FU head, and they never came with combustion rings, only 2RK/3BN's?
A Flat top piston doesn't interfere with your transfer ports as much as a Domed piston, so you can take advantage of scavenging with correct porting and a proper exhaust,
The 4FU seems to have larger volume crankcase transfers than a 3MB?
I'm running .6mm squish and a 134cc heavy Top end porting on a 3MB barrel. Looking at 25bhp maximum on 97octane. Most power will be made by the cylinder head itself, the barrel is aiding it along.
No doubt moving torque, and not that much more of it to very high RPM, will only make you come to be very efficient at going up and down the gearbox quicker to keep the thing in the right rev range.
Depends what you want from it, i'd say get the ports cleaned up, but don't change the Port timings at all, and just run her standard. These engines don't make power at all like a Rotax!
I've been bulding a race setup for mine for a while now, yet to know proper results tho
-
This post is deleted!
-
@Darty Here was my 4FU
As said I don't know natively if it supports domed, but certainly if you removed that ring and reworked the head
https://c1.staticflickr.com/1/440/30800032804_7635f2db5c_c.jpg
https://c1.staticflickr.com/1/431/31525983671_ea3ee375cf_c.jpg
Mine might have been modified, the crown seems very different. No signs of a heavy skim. it's a closer match to a P' stamped head but with a squish height less than .5, A domed piston would crash into it at that point.
A base gasket would help, but then you begin to change port timings, not good. I gave up on a 4FU, Nicasil is expensive if you lunch the bore up.
-
Another purchase sees the trail tech vapor and indicator dash added to PROJECT TDR.
I purchased the kit on eBay from Moore speed racing for £150 all in which I thought was a good deal.
Any of you guys run the vapor on a tdr/Dt before?
-
I always thought replacing my TDR clocks with something like this would look a bit out of place as the stock one moulds nicely into the plastics. Bet theres a big hole there now!
@Mightyman I have thought about the same problem but how about 3d printing a new speedo surround then fibre glassing bondo, filler paint to finish ?
-
@Mightyman I have thought about the same problem but how about 3d printing a new speedo surround then fibre glassing bondo, filler paint to finish ?
@tdr125greg That is a very nice idea actually! Would be even better if you could save the fussing with fibre glass and just get a snug fit with something 3D printed.
-
-
@finnerz89 looks tidy mate, how responsive is the Rev meter and do you have the radiator temp sensor or the sensor that goes on the spark plug?
-
Another purchase sees the trail tech vapor and indicator dash added to PROJECT TDR.
I purchased the kit on eBay from Moore speed racing for £150 all in which I thought was a good deal.Any of you guys run the vapor on a tdr/Dt before?
-
@tdr125greg vapor on my dt and I love it. Makes me feel like I got a spaceship at night with the shift lights flashing in my goggles. Haven't ridden the bike for years but back when I was a kid
-
@Calum I'm really looking forward to seeing those shift lights in action
@tdr125greg The one I fitted to my MT-03 was SUPER inaccurate with the rev counter... I fitted it to the spark plug wire as the instructions mentioned but at 60mph+ speed the revometer would be all over the place, claiming I needed to shift all the time
