CB750 scrambler project
-
@Louis-DT-WR this looks amazing, well done
wrote on 4 Apr 2020, 16:49 last edited by@rolz82 thank you, working through all the electrics. My least favourite thing
-
wrote on 4 Apr 2020, 19:04 last edited by
Wow, this looks gnarly as fuck!
-
wrote on 15 Apr 2020, 11:35 last edited by
Working through the electrics. I've got my rear indicators and tail lights sorted.
I made a CDI holder to relocate it.
Fuse box and indicator regular relocated.
Front lights, indicators and horn on.
Ignition barrel relocation plate made.
Just sorting a battery box and the battery is on order. I can't fully test what connector goes where until the battery comes.
-
wrote on 22 Apr 2020, 14:53 last edited by
Well I put the engine in alone which was a very heavy task
killed my back haha. Lining it up with the mounts while the bike was leaning again the bench. (You can't fit the engine when the chassis is on a bike lift)Got my battery box mounted with the lithium battery. Its so light! I thought it was just a empty case!
Carbs on + filters and cables. Fitting the carbs was tricky, the rubber manifolds are so hard. I'd replace them but £150+vat for 4 and they're not cracked.
-
Well I put the engine in alone which was a very heavy task
killed my back haha. Lining it up with the mounts while the bike was leaning again the bench. (You can't fit the engine when the chassis is on a bike lift)Got my battery box mounted with the lithium battery. Its so light! I thought it was just a empty case!
Carbs on + filters and cables. Fitting the carbs was tricky, the rubber manifolds are so hard. I'd replace them but £150+vat for 4 and they're not cracked.
wrote on 22 Apr 2020, 14:55 last edited byI even have a engine lift but it would have needed an offset cradle made up to clear the frame
-
wrote on 22 Apr 2020, 14:58 last edited by
That does look smart as f to be fair!
-
wrote on 22 Apr 2020, 15:15 last edited by
@Calum cheers man. Its literally a case of getting parts in my hands and making it fit/fabricate parts. I wish fowler's would hurry up, waiting ages for my rear brake parts. And side stand bits
-
wrote on 24 Apr 2020, 17:39 last edited by
Little bits done, oil cooler fully connected, the pipes were bent, took a while to get them right.
Oil filter came finally.
PCV filters on.
Started seat mounts and ignition switch relocation.The 2 most expensive items I need is an exhaust and starter motor.
Still undecided what tank colour. I'm thinking Matt gunmetal grey. I was going to go black but think that would be over kill.
-
Little bits done, oil cooler fully connected, the pipes were bent, took a while to get them right.
Oil filter came finally.
PCV filters on.
Started seat mounts and ignition switch relocation.The 2 most expensive items I need is an exhaust and starter motor.
Still undecided what tank colour. I'm thinking Matt gunmetal grey. I was going to go black but think that would be over kill.
wrote on 24 Apr 2020, 20:27 last edited by@Louis-DT-WR match your tank to the cam covers maybe
-
Little bits done, oil cooler fully connected, the pipes were bent, took a while to get them right.
Oil filter came finally.
PCV filters on.
Started seat mounts and ignition switch relocation.The 2 most expensive items I need is an exhaust and starter motor.
Still undecided what tank colour. I'm thinking Matt gunmetal grey. I was going to go black but think that would be over kill.
wrote on 24 Apr 2020, 23:24 last edited by@Louis-DT-WR You'll be too scared to get that beast dirty for-sure!!!
-
@Louis-DT-WR match your tank to the cam covers maybe
wrote on 25 Apr 2020, 12:05 last edited by@declan satin silver would be nice but not too stealth.
-
@Louis-DT-WR You'll be too scared to get that beast dirty for-sure!!!
wrote on 25 Apr 2020, 12:06 last edited by@NINJA always the case but haven't gone OCD on this. Its got scratches and scruffs on the engine and forks. And I like it looking ragged
-
wrote on 6 May 2020, 16:26 last edited by
Lights check on.
Tail lights seem to have not power, maybe but headlight is on when ignition on. Brake lights not working
maybe it will when engine is running.?Horn was faulty,
All 4 indicators would flash, so I had it wire in a diode and earth the dial indicator light
Clutch hydraulic line arrived and installed.
Tank painted, I have a decal coming for it.
Ignition switch installed -
Lights check on.
Tail lights seem to have not power, maybe but headlight is on when ignition on. Brake lights not working
maybe it will when engine is running.?Horn was faulty,
All 4 indicators would flash, so I had it wire in a diode and earth the dial indicator light
Clutch hydraulic line arrived and installed.
Tank painted, I have a decal coming for it.
Ignition switch installedwrote on 6 May 2020, 17:13 last edited by@Louis-DT-WR looks amazing pal, well done great build
-
@Louis-DT-WR looks amazing pal, well done great build
wrote on 6 May 2020, 17:52 last edited by@rolz82 thanks! I have such little knowledge of this bike (electrics and engine)
So many little things I want to know. -
wrote on 13 May 2020, 14:35 last edited by
All lights, switches and horn are on and functional
Seat brackets made up.
Waiting for my starter motor to arrive.
Then decide what way to go for exhaust.
-
wrote on 13 May 2020, 19:01 last edited by
Now this would get my attention at a local bike night, any plans to paint it or just keep the flat steel look?
-
Now this would get my attention at a local bike night, any plans to paint it or just keep the flat steel look?
wrote on 14 May 2020, 08:48 last edited by@Stevie-Wonder thanks. The tank is painted. In chrome silver powder coat. I was going to go all black but I wanted it to shine a bit
-
wrote on 4 Jun 2020, 13:28 last edited by
Took so many attempts to get the starting circuit to work. Checked everything, earths, relays, switches, batteries, motor and cables.
The first lithium battery I bought was total crap, couldn't crank the engine over even though cross reference numbers said it was correct. Bought a shido and works perfectly.
Made a numbplate holder + front "number plate"
The most exciting part is the exhaust! Cut off about 10kg of the baffles. Shortened the silencers right down and made up the end covers.
Still got to wrap the exhaust
-
wrote on 4 Jun 2020, 14:28 last edited by
Looks properly smart that!
